Recommended, 2024

Editor'S Choice

Crochet patternChicken cap with zigzag pattern

This hanger is in demand. With the beautiful berry tone, the cap fits perfectly into the autumnal landscape. Here you will find the instructions.

Photo: Schachenmayr



You need this:
Cap circumference 54 cm

  • 150 g in berry, Fb 07933
  • 1 crochet hook 5 mm
  • 1 embroidery needle

Spiral Rd: When crocheting in Spiral Rd, crochet the stitches continuously without closing the round (Rd) with a slit stitch. Use a contrasting yarn to mark the beginning of the round.

Zigzag pattern: Work in Rd as per crochet pattern 1. Mesh number divisible by 3. The 1.-6. Crochet Rd 1x, then the 3.-6. Always repeat Rd.

Thread ring: To do so, put a loop and pull the thread through the crochet hook as for an initial stitch, do not tighten the thread, but keep the loop loose. Now for the first stitch loop the thread around the needle and crochet the stitch. Crochet the corresponding number of stitches in the thread ring and close the 1st round with a warp stitch in the upper stitches of the initial stitch. Now tighten the thread end so that the ring is tightly closed.

Note: The hat is crocheted from top to bottom.

Stitch: in chopsticks (= tr): 10 tr x 10 rounds / rows = 10 x 10 cm.

manual

Put a thread ring for the cap tip.
1st round: Crochet 3 sts (replacement for 1st tr), 17 tr in the thread ring.
2nd round: crochet the 1st tr in the uppermost spare mesh of the pre-round, marking the beginning of the round with contrasting yarn (= back center), * 3 tr in 1 stitching point, 2 tr, repeat from * 4x, 3 tr in 1 puncture site, 1 tr = 30 tr.
3rd round: 2 tr, * 3 tr in 1 puncture site, 4 tr, repeat from * 5x, 3 tr in 1 puncture site, 2 tr = 42 tr.
4th round: 3 tr, * 3 tr in 1 puncture site, 6 tr, repeat from * 5x, 3 tr in 1 puncture site, 3 tr = 54 tr.
5th round: 4 tr, * 3 tr in 1 point, 8 tr, repeat from * 5 times, 3 tr in 1 point, 4 tr = 66 tr.
6th round: 5 tr, * 3 tr in 1 puncture site, 10 tr, repeat from * 5x, 3 tr in 1 puncture, 1 tr, 2 half tr and 2 fixed loops = 78 stitches.
ROUND 7: Crochet 1 sliver in the following stitch, 1 slit (substitute for 1st slit), work 77 slits in each of the back loops, close Rd with 1 slit stitch into the initial slit.
8th 9th Rd: 1 air stitch (substitute for the 1st stitch), work 77 sts in each of the back stitches, close the Rd with 1 slit stitch in the initial mesh.
10th-19th Rd: work in a zigzag pattern according to crochet script, the grayed Rd shows the previous Rd fixed stitches.
20th-22nd Rd: 1 air stitch (substitute for the 1st stitch), work 77 sts in each of the back stitches, close the Rd with 1 slit stitch in the initial mesh. Cut the thread.

Left earflap: For the left earflap from the Rd transition (= rear center) into the 11th stitch connect the thread and work according to crochet instruction 2 in fixed stitches. Crochet the right earflap in the same way, but tie the thread on the 23rd stitch to the right of the Rd transition.

Completion:
Tighten the thread ring at the tip of the cap, sew all the threads. Crochet the lower edge of the cap, including the edges of the ear flaps with 1 back hem. The upper M-limbs lie to the inside of the cap and make a nice border. Now make a pompon of 8 cm in diameter and sew it slightly to the front between the 1st and 2nd round) on the top of the hat.

Click here for the crochet font.

Popular Categories

Top